Not in the new shop yet

Delivered anywhere in the UK

How to Apply Window Vinyl Without Bubbles

Clean the glass until it squeaks, fit on a dry day above 10 degrees, tape the vinyl in place before you peel anything, then squeegee from the middle outwards in firm, overlapping strokes. Most bubbles come from dust, a cold or damp surface, or peeling the backing off in one go.

Each of our window products goes on a little differently: lettering comes on application tape, printed graphics go on the outside of the glass, frosted film goes on the inside, and clings hold by static with no glue. If you would rather not fit it yourself, we can arrange fitting on a quote.

By the Liberty Signs team · Updated 22 Nov 2026 · 4 min read

What You Need

  • A plastic squeegee, ideally with a felt edge so it does not scratch the vinyl or the tape.
  • Masking tape, to hold the vinyl in position while you check it is straight.
  • A tape measure and a pencil or a few small bits of tape, to mark where it goes on the frame.
  • Glass cleaner and lint-free cloths. Use a plain cleaner, not one that leaves a shine or a coating.
  • A sharp craft knife, only for trimming a panel to the frame, and only on the glass, never into the seals.
  • A second person for anything wider than your arms. Big panels are much easier with two.

Wind, rain and direct hot sun all make fitting harder, so pick a calm, dry day, or work from inside where the vinyl goes on the inside of the glass.

Clean and Check the Glass

Vinyl sticks to whatever is on the glass, so dust and grease under it are the main cause of bubbles and specks. - Wash the glass with soapy water to lift dirt, then rinse and dry it fully. - Clean it again with glass cleaner and a fresh lint-free cloth. Pay attention to the corners and the edges by the frame. - Wait until it is completely dry. Any moisture left under dry-fit vinyl shows as cloudy patches or bubbles. - Check the temperature. Apply above 10 degrees. On a cold morning the adhesive is stiff and does not grab; in direct hot sun it grabs too fast to adjust.

Our window products are made to be fitted dry. If you are used to fitting another way, ask us before you start.

Lettering and Cut Graphics on Application Tape

Vinyl lettering comes weeded and on application tape, a clear or paper layer that holds every letter in its place. Printed window graphics cut to shape come on application tape too. - Position it first. Hold the whole piece on the glass, backing still on, and check it is level with a tape measure from the frame. Tape it along the top edge to make a hinge. - Peel and squeegee. Lift the piece up on its hinge, peel the backing away, then lower it slowly while you squeegee from the top down, from the middle out to the sides. - Go over it again. Firm, overlapping strokes push out the air and press each letter down through the tape. - Peel the tape back slowly, folding it back flat against itself rather than pulling it straight out. If a letter lifts with the tape, lay it back down and rub over it again.

For very wide pieces, tape a hinge down the middle instead and work one half at a time. If you chose Inside of the Glass, the lettering is cut mirrored, so it reads correctly from the street once it is on the inside.

Printed Panels, Frosted Film and Clings

  • Printed window graphics go on the outside face of the glass. For a square cut panel, tape it in place, peel back a strip of backing at the top, fix that edge, then pull the backing away a little at a time as you squeegee down. Large windows are printed in panels that meet on the glazing bars, so fit one pane at a time.
  • Frosted window vinyl goes on the inside of the glass as standard. Fit it the same way: hinge, peel a little, squeegee, repeat. Pieces wider than 1524mm come in joined widths, so line up the second piece with the first along the join. For big panes, the Premium Bubble-Free Frost option on the product page is easier to get flat.
  • Window clings have no glue. Clean the inside of the glass, press the cling on from the middle out and smooth it with a squeegee or a soft cloth. If it is not straight, lift it and try again.

Measure the visible glass inside the frame before you order, so each piece fits the pane without trimming.

Small Bubbles and Letting It Settle

A few small bubbles are normal on a fresh fit. Push each one towards the nearest edge with your squeegee. If one will not move, prick it with a fine pin at one side and press the air out with your thumb.

Give the vinyl a few days to settle before you wash the glass, and then clean it gently with soapy water and a soft cloth, wiping along the edges rather than into them. Our guide to cleaning and caring for signs has more on looking after it.

Not sure which window vinyl to choose? Read window vinyl explained first.

Common Questions

  • Usually dust or grease on the glass, a cold or damp surface, or peeling all the backing off at once. Clean the glass twice, fit above 10 degrees and peel the backing a little at a time as you squeegee.
  • Our window products are made to be fitted dry, as described on each product page. If you want to fit another way, ask us first.
  • Yes. Vinyl lettering is weeded and supplied on application tape, so the letters stay in place while you position and fit them. Printed window graphics cut to shape come on tape too.
  • Yes. Fitting is not included, but we can arrange fitting on a quote.
  • ChloeChloeAndreaAndreaWilliamWilliamTalk to Our Team0161 399 0695Mon–Fri 8:00 to 16:30Visit SupportSend us a message or check an orderOr message us onWhatsApporEmail

Letter Your Window

Enter the size of your design in mm and see the price straight away. Approve your proof online, or send it to us to check first.